Two-component elastomer sealant and self-levelling based on polysulphide.

LASTOIS PSF

ÂĄCompĂĄrtelo o guĂĄrdalo!

LASTOIS PSF , Two-component elastomer sealant and self-levelling based on polysulphide.

LASTOIS PSF

Two-component elastomer sealant and self-levelling based on polysulphide.

Ficha TĂ©cnica

Description Two-component elastomer sealant and self-levelling based on polysulphide., LASTOIS PSF ?

LASTOIS PSF is a two-component elastic sealant based on polysulphide with high chemical resistance. Suitable for indoors and outdoors. Resistant to permanent immersion. It is used for sealing joints in concrete, tanks and canals, on concrete floors, industrial warehouses, stores, parkings, airports, joint sealing in contact with chemical agents.

Aplication Two-component elastomer sealant and self-levelling based on polysulphide.?

LASTOIS PSF is applied for sealing concrete joints, joints in permanent immersion, sealing of joints in canals, water tanks, floors of industrial warehouses, floors of stores, parkings, airports, joints in contact with chemical agents.

Features and Benefits de LASTOIS PSF , Two-component elastomer sealant and self-levelling based on polysulphide.

  •   HIGH ADHERENCE
  •   HIGH CHEMICAL AND MECHANICAL RESISTANCE
  •   RESIST PERMANENT IMMERSION
  •   ELASTIC IN A BIG RANGE OF TEMPERATURES

ÂĄCompĂĄrtelo o guĂĄrdalo!

Surface preparation

The support must be clean, dry and cured. (28 days for mortars and concretes).

Modes of application Two-component elastomer sealant and self-levelling based on polysulphide.?

  The recommended thickness of sealing are from 8 to 40 mm. - In general the depth of sealant must be the half of the width. Until 15 mm of width and the depth will be the same. - Is recommendable to use a base of joint such as JUPO to limit and avoid not desired tensions in the bottom of the joint. - To improve the adherence on porous supports a special primer such as IMPRIDUR or LASTOIS PSF must be applied. - It is introduced in two component which are mixed before applying. - The admixture must be done with a low revolution driller (300-400 rpm) provided with a rod free of air, mixing for 5 minutes until achieve an homogeneous colour. - The edges of joint must be protected with tape in order to avoid spots. - Pour it on the joint once the primer dries. - Avoid the application in exteriors whith rain forecast after the application. - The proper temperature for doing the work must be between 10ÂșC and 30ÂșC. - DonÂŽt apply with temperatures below 5ÂșC. - DonÂŽt apply with Relative Humidity over 90%. - Avoid applications with high temperatures, strong sunlight or wind. - Usable after 72 hours (20ÂșC and 50% Relative Humidity).

Clean up

The tools must be cleaned with EPOXY SOLVENT while they are still wet.

Performance Two-component elastomer sealant and self-levelling based on polysulphide.

100 cc/ml for joints of 10x10 mm

Storage Two-component elastomer sealant and self-levelling based on polysulphide.

18 months in their original packages protected from the weather and stored in cool and dry places.

Documentation Two-component elastomer sealant and self-levelling based on polysulphide.

Productos relacionadas

LASTOIS MS FAST,

LASTOIS MS FAST

MÁS INFO
LASTOIS POL, ELASTOMERIC POLYURETHANE PUTTY

LASTOIS POL

ELASTOMERIC POLYURETHANE PUTTY

COMPRARMÁS INFO
LASTOIS POL LIQUIDO, SEALANT BASED ON TWO COMPONENT POLYURETHANE RESINS IN FLUID CONSISTENCY

LASTOIS POL LIQUIDO

SEALANT BASED ON TWO COMPONENT POLYURETHANE RESINS IN FLUID CONSISTENCY

COMPRARMÁS INFO
LASTOIS SPT, Traslucent polymer sealant.

LASTOIS SPT

Traslucent polymer sealant.

MÁS INFO
+34 981 602 111
ÂżTienes dudas?
LlĂĄmanos
MÁXIMA CALIDAD.
En materias primas
y construcciĂłn.
logo de teais, empresa de materiales de construcciĂłn
Avda. da EnerxĂ­a, nÂș 153, Pol. Ind. de SabĂłn
15143 Arteixo,A Coruña
Phone.: 981 602 111
Fax.: 981 601 508
Email.: desarrollo@teais.es

sĂ­guenos en:

PolĂ­tica de cookies | Aviso Legal | PolĂ­tica de privacidad

FEDER INNTERCONECTA

2015-2017 SHIAC (ITC-20151250): DESARROLLO DE TECNOLOGÍAS DE HIGIENIZACIÓN PARA LA REDUCCIÓN DE RIESGOS BIOLÓGICOS EN ACUICULTURA
El proyecto SHIAC tiene como objetivo principal la investigaciĂłn y desarrollo de una estrategia integral que permita reducir el riesgo biolĂłgico en acuicultura, integrando diferentes medidas tanto de tipo activo como pasivo para la prevenciĂłn de patologĂ­as con una gran incidencia econĂłmica en el sector, y aportando soluciones mĂĄs sostenibles ambientalmente a las actualmente empleadas en acuicultura.
Grupo Tres Mares S.A actĂșa como socio representante del consorcio empresarial que ejecuta este proyecto el cual ha sido aprobado y subvencionado por CDTI en el marco de la convocatoria FEDER INNTERCONECTA 2015.